Selecting Greenhouse Film Properties: Thickness, UV Ageing And Fault Diagnosis

Introduction

Greenhouse film is a thin polymer sheet stretched over a frame, and almost everything growers expect from it depends on properties that are not visible in a sample. Two sheets of the same nominal thickness can behave very differently depending on how the polymer was made, how much ultraviolet stabiliser it contains and how tightly it is tensioned. This article explains what the main properties mean in practice, why condensation collects beneath the skin, and how to diagnose the failures that appear year after year. The aim is diagnostic rather than promotional, because film choices are made once at installation but their consequences run through a whole season.

The Properties That Decide How Film Performs

Thickness is the headline specification, and the least informative on its own. It is usually expressed in microns or in mils, and typical agricultural film for greenhouse covering falls in the broad range of roughly one hundred to two hundred and fifty microns, with heavier gauges used where wind exposure or snow loading is significant. Thicker film resists tearing and holds tension better, but it is also heavier per square metre, which means more wind load on the fixings and a larger sag if the tensioning is uneven. Because the strength of a stretched film comes from the combination of gauge, weave structure and the level of stretch, two films of equal thickness are not interchangeable.

Light transmission describes how much of the incident light passes through the film. Even a clear film typically transmits somewhat less than a clear glass pane because of surface reflection and absorption in the polymer, and the difference between products can be wide. For crops that depend on light, this figure deserves attention, but it should be read together with haze and diffuseness. A film that scatters light more evenly often produces a better canopy distribution than a highly transparent film that concentrates light on the top of the crop, and many growers find that a slightly diffusing film outperforms a clearer one even though the headline transmission number is lower.

Ultraviolet stabilisation determines how quickly the film degrades. Continuous UV exposure breaks polymer chains, and the film loses strength, yellows and eventually shreds along the folds where it was creased during installation. Films intended for a single season and films intended for multi-season use differ mainly in stabiliser load and in base polymer, not in thickness alone. Where a film is expected to remain in place for several seasons, the relevant question for the supplier is the expected service life under the local radiation and temperature profile, because that profile varies enormously between a mild coastal site and a high-altitude summer.

Anti-Drip And Condensation Behaviour

Condensation under the film skin is the most common complaint about greenhouse covering, and it is worth separating the physics from the marketing. Warm, moist air inside the house contacts the film, which is cooler than the air because the outside temperature is lower. The vapour in that air condenses on the inner surface when the surface falls below the dew point of the inside air. This happens every night in almost every greenhouse. The relevant question is not whether condensation occurs, but whether it runs off as large drops, forms as a fine fog, or stays as droplets across the whole surface.

Fine fog or a uniform droplet field changes little light and spreads evenly when it runs off. Large heavy drops form where the film is nearly vertical, and they fall onto the same patch of crop repeatedly. That repeated wetting promotes fungal problems and reduces the effective light reaching the canopy in the early hours. Anti-drip or anti-fog treated films are designed to change the wetting behaviour of the inner surface so that moisture forms as many small droplets rather than a few large ones, allowing the film to clear itself more evenly as the day warms.

Ventilation is the other half of the answer. Fans and vents remove the vapour that produces the condensation in the first place, and a film treated to manage droplets will still perform badly in a structure where humidity is allowed to build unchecked. Condensation complaints are frequently a humidity control problem that presents itself as a covering problem.

Types Of Greenhouse Film And Their Trade-offs

Film families differ in base polymer and in how they are formulated, and each carries a different balance of properties. The table below summarises the common families and the situations they suit.

Film familyStrengthsTrade-offsTypical use
Polyethylene, single layerLow cost, good light transmission, easy to installShortest service life, degrades faster under strong UVSingle season houses, temporary covers
Polyethylene, multi-layer with UV stabilisationLonger life, better tear resistance, retains clarity longerHigher cost, heavier, needs correct tensioningMulti-season production houses
Anti-drip treated filmForms small droplets that clear more evenlyAdded cost, benefits reduce as the film agesHouses with high humidity or dense planting
Diffusing or light-scattering filmSpreads light deeper into the canopySlightly lower total transmissionHigh density crops with limited light
Reinforced or reinforced-laminate filmResists hail and puncture, longer lifeHeavier, more expensive, more sensitive to fittingExposed sites, hail-prone regions
Insulating double-layer systemsRetains warmth, reduces fuel use at nightMore complex to install and maintainWinter production, overwintering

Whatever the family, practical differences show up in the installation rather than in the roll. Film stretched too tight develops residual stress and tears along the fixings when it cools overnight. Film that is slack flaps in the wind, and the flapping destroys it faster than steady wind load. Correct tension is the factor that most extends the life of an otherwise sound film.

Tensioning, Fixings And The Role Of The Profile

Film is normally fixed to an aluminium profile or to a batten that runs along a structural member, and the profile captures a rolled edge of the film. Fixings are placed at regular intervals, and the spacing between them determines how much the film can flex between points. Too widely spaced and the film flaps; too closely spaced and the profile line becomes a rigid ridge that concentrates stress and creates a crease line down the length of the structure.

Crease lines matter more than most growers expect. A film that is folded sharply when it is rolled onto the profile has a permanent weak line along the fold, and under thermal cycling that line widens into a tear. This is one reason film should be unrolled along the length of the house in the shade, at a time of day when the sheet is not hot, and installed without stretching it across the width in one violent movement. Where the film must be cut, cut it with a sharp tool in a single pass, and never cut it on a crease.

Overlapping sections on a pitched roof should be arranged so that water runs down the overlap rather than into it, and the overlap should be long enough that wind cannot lift it. On a multi-span structure the profile line at each span junction is the highest stress concentration in the whole covering, and it deserves particular care during installation.

Diagnosing Common Greenhouse Film Faults

Film problems are usually reported by symptom. Working from symptom to cause is faster than replacing the sheet and hoping, and it tells you whether the fault will recur. The table below sets out the faults that come up most often.

SymptomLikely causeWhat to check firstPriority
White or milky haze over part of the sheetCondensation from inside rather than external moistureHumidity levels overnight and ventilation runningModerate
Yellowing and brittleness after one seasonUV degradation of the polymerAge of the film and the local radiation exposurePlan replacement
Split along a straight lineCrease or stress line where the film was foldedWhether the tear follows a roll fold or fixing lineRepair promptly
Small holes near fixingsAbrasion against a sharp profile edgeProfile edges and the spacing of screwsRepair promptly
Large tear after a stormFilm too slack or too thin for the wind loadTension, gauge and prevailing wind directionUrgent
Film lifting at the ridgeProfile fixing failure or insufficient overlapRidge profile fixings and the overlap lengthUrgent
Water pooling in a low areaSag from uneven tension or unsupported spanFrame spacing and intermediate supportsModerate
Droplets falling on one bed onlyCondensation running down a steep sectionSlope of the film and airflow under that bayModerate

Two principles help when reading this table. A fault that appears in the same place every year is a design or installation problem, not a material defect. A fault that appears suddenly after a weather event is usually the consequence of a condition the covering had been tolerating for months, such as persistent slackness or a section that finally gave way.

Repairing Film Without Replacing The Whole Cover

Most field failures are repairable with compatible patching tape or a patch of matching film, provided the surface is clean and dry and the patch is larger than the damaged area on every side. Patching in warm, dry conditions gives a better bond than patching in damp weather, and the patched film should be weighted down or held by the profile for a period so that the adhesive or heat-welded bond sets fully. A patch over a tear that is still under tension will simply tear again, so the area should be tensioned back to a neutral position first.

Repairs are a short-term measure. A covering that needs repeated patching has usually reached the end of its useful life, because degradation is progressive and the next failure is rarely far away. Replacing the film at the correct tension, with new fixings and fresh profiles where needed, restores the covering to a known condition and usually outperforms a heavily patched sheet for the rest of the season.

Seasonal Care And A Simple Inspection Routine

A regular inspection routine catches most problems early. Walk the length of each side and under each ridge line and look for lifting edges, tension changes and new tears. Check the fixings where the film meets the profile, particularly at the ends of the structure and at doorways where the film is handled most often. Clean the film where it has become heavily soiled, since a dirty surface reduces the light reaching the crop and can also hold moisture against the sheet.

Record the date the film was installed and the product used. That note saves guesswork the following year, because it turns the question of whether to renew into a comparison against actual experience. Where a structure uses different films on the roof and the sides, that difference is often rational, since the roof takes the full radiation while the sides take the weather, but it should be a deliberate choice.

Conclusion

Greenhouse film performs as a system of properties and installation quality rather than as a single number on a roll. Thickness influences strength and wind load, ultraviolet stabilisation governs how long the sheet stays usable, light transmission and diffuseness shape the light the crop actually receives, and the wetting behaviour of the inner surface determines whether condensation presents as harmless fog or repeated wetting on the same crop row. Installation determines the outcome as much as the product does: correct tension, sound fixings, clean profile edges and folds avoided during handling prevent the majority of early failures. Diagnosing faults from the symptom, using the table above as a starting point, allows a small tear to be repaired quickly and a genuinely degraded covering to be replaced at the right time of year rather than in the middle of a critical growth stage.

27 次